• <sub id="h4knl"><ol id="h4knl"></ol></sub>
    <sup id="h4knl"></sup>
      <sub id="h4knl"></sub>

      <sub id="h4knl"><ol id="h4knl"><em id="h4knl"></em></ol></sub><s id="h4knl"></s>
      1. <strong id="h4knl"></strong>

      2. 思科幀中繼點對多點子接口配置實例解析

        時間:2024-08-15 07:02:57 網絡技術 我要投稿
        • 相關推薦

        思科幀中繼點對多點子接口配置實例解析

          Cisco ACE是一個很常用的配置,下面小編為大家介紹了Cisco ACE的一個基本配置實例,希望大家能夠輕松掌握。

          幀中繼點對多點子接口拓撲圖如下:

          步驟一:配置R4的為幀中繼交換機。

          R4(config)#frame-relay switching //啟用frame-relay 交換

          R4(config)#interface serial 1/0

          R4(config-if)#encapsulation frame-relay

          R4(config-if)#frame-relay intf-type dce

          R4(config-if)#frame-relay lmi-type cisco (默認類型)

          R4(config-if)#frame-relay route 100 interface serial 1/1 101

          R4(config-if)#frame-relay route 200 interface serial 1/2 201

          R4(config-if)#clock rate 64000

          R4(config-if)#no shutdown

          R4(config-if)#exit

          R4(config)#interface serial 1/1

          R4(config-if)#encapsulation frame-relay

          R4(config-if)#frame-relay intf-type dce

          R4(config-if)#frame-relay lmi-type ansi

          R4(config-if)#frame-relay route 101 interface serial 1/0 100

          R4(config-if)#clock rate 64000

          R4(config-if)#no shutdown

          R4(config-if)#exit

          R4(config)#interface serial 1/2

          R4(config-if)#encapsulation frame-relay

          R4(config-if)#frame-relay intf-type dce

          R4(config-if)#frame-relay lmi-type q933a

          R4(config-if)#frame-relay route 201 interface serial 1/0 200

          R4(config-if)#clock rate 64000

          R4(config-if)#no shutdown

          步驟二:配置R2路由器

          R2(config)#interface serial 1/2

          R2(config-if)#encapsulation frame-relay //在接口下啟用幀中繼的封裝

          R2(config-if)#ip address 172.16.1.2 255.255.255.0

          R2(config-if)#no shut

          步驟三:配置R3路由器

          R3(config)#interface serial 1/2

          R3(config-if)#encapsulation frame-relay

          R3(config-if)#ip address 172.16.1.3 255.255.255.0

          R3(config-if)#no shut

          步驟四:配置R1,采用多點子接口,配置R1的幀中繼

          R1(config)#interface serial 1/2

          R1(config-if)#encapsulation frame-relay

          R1(config-if)#no ip add

          R1(config-if)#no shut

          R1(config-if)#exit

          R1(config)#interface serial 1/2.1 multipoint

          R1(config-subif)#ip address 172.16.1.1 255.255.255.0

          R1(config-subif)#frame-relay map ip 172.16.1.2 100 broadcast

          R1(config-subif)#frame-relay map ip 172.16.1.3 200 broadcast

          R1(config-subif)#exit

          R1(config)#exit

          步驟五:在R1使用show frame-realy lmi,show frame-relay pvc進行確認。

          步驟六:在R1,R2,R3上配置RIP,進行觀察。

          幀中繼點對多點子接口配置結果:R1,R2,R3能夠正確的學習到所有的路由。

        【思科幀中繼點對多點子接口配置實例解析】相關文章:

        思科DHCP服務器配置實例解析07-25

        思科三層交換機配置實例及命令10-24

        思科配置命令詳細介紹01-23

        EIGRP帶寬實例配置09-19

        思科交換機的基本配置09-10

        思科交換機配置vlan09-02

        思科路由器的安全配置06-03

        思科路由器配置基礎08-13

        思科交換機STP配置08-30

        cisco思科交換機配置篇08-01

        国产高潮无套免费视频_久久九九兔免费精品6_99精品热6080YY久久_国产91久久久久久无码
      3. <sub id="h4knl"><ol id="h4knl"></ol></sub>
        <sup id="h4knl"></sup>
          <sub id="h4knl"></sub>

          <sub id="h4knl"><ol id="h4knl"><em id="h4knl"></em></ol></sub><s id="h4knl"></s>
          1. <strong id="h4knl"></strong>

          2. 亚洲色婷婷综合久久 | 亚洲男同帅gay片在线观看 | 日本精品专区一二三区 | 日韩欧美校园一区二区 | 亚洲中出在线视频 | 婷婷色香五月综合缴缴情 |